Resources Wanted
Six one l/i" head pins
2" four x 1 mm sterling silver rectangle wire Two one' parts of sterling silver chain Two pearl beads
Two 1.four mm round sterling silver beads Two sterling silver ear wires
Instruments Required
Ruler
Marker
Jeweler's observed or tin snips Safety Eyeglasses Hard, flat area Awl
Hammer /Ίί" drill little bit
Handheld rotary Device, flex shaft, or drill push File
Fantastic grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Wire cutters or tin snips
Spherical nose pliers
1.Utilize the ruler to measure and mark two Γ items of four x 1 mm rectangle sterling silver wire.
two.Using a jeweler's noticed or tin snips, Slash the 4 x one mm rectangle sterling silver wire into two Γ lengths.
3.File Each individual finish with the 1" rectangle wire items to eliminate any burs or rough edges; You should utilize the file to round the finishes of your rectangle wire items In order for you. Use a wonderful grit sanding pad to go over the realm in which you have filed to easy the sides and remove any file marks.
four.Utilize the ruler to measure and mark '/*’ from Every single end in the Γ parts of rectangle wire and location a mark in the middle of your wire. This may be in which you drill the holes to slip the head pins by way of.
5Next, set in your basic safety Eyeglasses! Then location the Γ rectangle wire items on to a hard, flat surface area. Position the point in the awl to the mark that you simply manufactured /(." from Each individual finish on the rectangle wire parts, and utilize a hammer to firmly strike as soon as on the highest of your awl. This will make a pilot hole for drilling holes in the rectangle wire.
six.Using a drill bit. drill holes into Just about every end from the rectangle wire items which has a handheld rotary tool, flex shaft, or drill press (even though continue to sporting your security Eyeglasses!).
seven.Use the file or fantastic grit sanding pad to remove any burs or tough edges left from drilling holes in to the rectangle wire items.
eight.Curve both of those Γ pieces of rectangle wire into a form employing a ring mandrel and rawhide mallet. If you don't have a ring mandrel and rawhide mallet, use two pairs of chain nose pliers. Holding one particular pair in Just about every hand, grasp Each individual finish in the Γ rectangle wire piece from the chain nose pliers and Carefully bend the rectangle wire right into a “C shape, aligning the holes which you drilled on Every single conclusion of the Γ rectangle wire pieces. Examine equally with the C-formed rectangle wire parts and adjust the curves so that they are equivalent in dimensions.
Established these apart.
nine.Use the ruler to measure the chain into Γ pieces. Make use of the wire cutters to chop the chain, and established these parts apart.
ten.Area a head pin via a pearl bead and then add a single 1.four mm sterling silver bead.
eleven.Utilize the ruler to evaluate and mark /t" higher than the very best bead on The pinnacle pin. With wire cutters or tin snips, Slice The pinnacle pin wire Yu," above the very best bead.
12.Utilizing the chain nose pliers, bend The top pin wire beside the best bead in a ninety-diploma angle.
13.Hold the head pin Using the pearl bead as well as the silver bead on it in a single hand Along with the wire you bent pointing towards you. Utilizing the spherical nose pliers, grip the top of The pinnacle pin wire that is pointing toward you and roll it away from you (consider turning the ignition important to start your vehicle). Release the pliers from The top pin wire. At this time, the opening inside the loop at the very best of The top pin wire must be massive ample to slide the Γ size of chain on it ahead of closing the loop of The top pin. Once you incorporate the chain, make use of the spherical nose pliers to grasp the loop of The top pin men's college ring wire and roll it closed. You can utilize the round nose or chain nose pliers to adjust the shape from the loop at the very best of the head pin if you have to.
14.Repeat this stage on the second pearl and silver bead. Set these apart.
fifteen.Put a head pin in the gap drilled into just one conclusion with the rectangle wire “C* form with The underside or flat stop on the inside curve from the rectangle men's college ring wire *C* shape. Use the ruler to measure and mark The pinnacle pin s/u.m higher than the rectangle wire. mens casual rings With wire cutters or tin snips, Slice The pinnacle pin wire earlier mentioned the highest in the rectangle wire.
16.Use silver rings for men the chain nose pliers to bend the head pin wire beside the rectangle wire in a ninety-diploma angle.
17.With all the chain nose pliers in one hand, hold The underside or flat area of The pinnacle pin firmly versus the men's jewelry rectangle wire with The pinnacle pin wire that you just bent pointing toward you.
Along with your other hand, use the round nose pliers to grip the top of The pinnacle pin wire and roll it from you. Release the head pin wire. At this point, the opening during the loop of The pinnacle pin wire need to even now be huge sufficient to slip the top backlink on the 1' chain onto iL Now increase the chain to your loop of The top pin. after which use the spherical nose pliers to grasp the loop of The pinnacle pin wire and roll it shut. You can utilize the round nose or chain nose pliers to regulate The form in the loop at the top of The pinnacle pin.
eighteen.Repeat this process on another gap from the C-formed rectangle wire. Rather than adding the one * size of chain Using the pearl and the sterling silver bead, increase the ear wire at the opposite stop. Slip the ear wire onto the loop of The pinnacle pin ahead of closing the loop.
19.Repeat the preceding ways on the 2nd earring.
